WARNING: This chapter describes classes that are obsolete.
These classes are normally not available when libg++
is installed normally. The sources are currently included
in the distribution, and you can configure libg++ to use
these classes instead of the new iostream classes.
This is only a temporary measure; you should convert your
code to use iostreams as soon as possible. The iostream
classes provide some compatibility support, but it is
very incomplete (there is no longer a
File class supports basic IO on Unix files. Operations are
based on common C stdio library functions.
File serves as the base class for istreams, ostreams, and other
derived classes. It contains the interface between the Unix stdio file
library and these more structured classes. Most operations are implemented
as simple calls to stdio functions.
File class operations are also fully
compatible with raw system file reads and writes (like the system
lseek calls) when buffering is disabled (see below).
FILE* stdio file pointer is, however maintained as protected.
Classes derived from File may only use the IO operations provided by File,
which encompass essentially all stdio capabilities.
The class contains four general kinds of functions: methods for binding
Files to physical Unix files, basic IO methods, file and buffer
control methods, and methods for maintaining logical and physical file
Binding and related tasks are accomplished via
File constructors and
destructors, and member functions
open, close, remove, filedesc,
If a file name is provided in a constructor or open, it is
maintained as class variable
nm and is accessible
name. If no name is provided, then
null, except that
Files bound to the default files stdin,
stdout, and stderr are automatically given the names
(stdin), (stdout), (stderr) respectively.
setname may be used to change the
internal name of the
File. This does not change the name
of the physical file bound to the File.
The member function
close closes a file. The
~File destructor closes a file if it is open, except
that stdin, stdout, and stderr are flushed but left open for
the system to close on program exit since some systems may
require this, and on others it does not matter.
closes the file, and then deletes it if possible by calling the
system function to delete the file with the name provided in
writeperform binary IO via stdio
putfor chars invoke stdio
put(const char* s)outputs a null-terminated string via stdio
putbackare synonyms. Both call stdio
tell call the
corresponding stdio functions.
fill() call stdio
setbuf is mainly useful to turn off buffering in cases
where nonsequential binary IO is being performed.
raw is a
setbuf(_IONBF). After a
the stdio functions instead of the system
etc., calls entails very little overhead. Moreover, these become
fully compatible with intermixed system calls (e.g.,
lseek(f.filedesc(), 0, 0)). While intermixing
and system IO calls is not at all recommended, this technique
does allow the
File class to be used in conjunction with
other functions and libraries already set up to operate on file
setbuf should be called at most once after a
constructor or open, but before any IO.
File status is maintained in several ways.
File may be checked for accessibility via
is_open(), which returns true if the File is bound to a
usable physical file,
readable(), which returns true if
the File can be read from (opened for reading, and not in a
_fail state), or
writable(), which returns true if the
File can be written to.
File operations return their status via two means: failure and
success are represented via the logical state. Also, the
return values of invoked stdio and system functions that
return useful numeric values (not just failure/success flags)
are held in a class variable accessible via
(This is useful, for example, in determining the number of
items actually read by the
Like the AT&T i/o-stream classes, but unlike the description in
the Stroustrup book, p238,
rdstate() returns the bitwise
_bad, not necessarily
distinct values. The functions
good() can be used to test for each of
these conditions independently.
_fail becomes set for any input operation that could not
read in the desired data, and for other failed operations. As
with all Unix IO,
_eof becomes true only when an input
operations fails because of an end of file. Therefore,
_eof is not immediately true after the last successful
read of a file, but only after one final read attempt. Thus, for
_eof almost always
become true at the same time.
bad is set for unbound
files, and may also be set by applications in order to communicate
input corruption. Conversely,
_good is defined as 0 and
is returned by
rdstate() if all is well.
The state may be modified via
despite its name, sets the corresponding state_value flag.
clear() with no arguments resets the state to
failif(int cond) sets the state to
_fail only if
cond is true.
Errors occuring during constructors and file opens also invoke the
error in turn calls a resetable error
handling function pointed to by the non-member global variable
File_error_handler only if a system error has been generated.
error cannot tell if the current system error is actually
responsible for a failure, it may at times print out spurious messages.
Three error handlers are provided. The default,
verbose_File_error_handler calls the system function
perror to print the corresponding error message on standard
error, and then returns to the caller.
does nothing, and simply returns.
prints the error and then aborts execution. These three handlers, or any
other user-defined error handlers can be selected via the non-member
All read and write operations communicate either logical or
physical failure by setting the
_fail flag. All further
operations are blocked if the state is in a
condition. Programmers must explicitly use
reset the state in order to continue IO processing after
either a logical or physical failure. C programmers who are
unfamiliar with these conventions should note that, unlike
the stdio library,
File functions indicate IO success,
status, or failure solely through the state, not via return values of
the functions. The
void* operator or
may be used to test success. In particular, according to c++
conversion rules, the
void* coercion is automatically
applied whenever the
File& return value of any
function is tested in an
for example, an easy way to copy all of stdin to stdout until
eof (at which point
get fails) or some error is
char c; while(cin.get(c) && cout.put(c));.
The current version of istreams and ostreams differs significantly
from previous versions in order to obtain compatibility with
AT&T 1.2 streams. Most code using previous versions should still
work. However, the following features of
File are not
incorporated in streams (they are still present in
scan(const char* fmt...), remove(), read(), write(),
setbuf(), raw(). Additionally, the feature of previous streams
that allowed free intermixing of stream and stdio input and output
is no longer guaranteed to always behave as desired.
Go to the first, previous, next, last section, table of contents.